Are fpv drone motors waterproof?

Aug 22, 2026

Leave a message

Many FPV pilots have wondered about this question: Can drone motors actually get wet? Can you fly in light rain? Will they be completely ruined if they fall into water? As FPV applications become more diverse, these questions have become particularly practical.

 

1

The truth about "waterproofing" in FPV brushless motors

Core conclusion: The vast majority of FPV brushless motors are not truly waterproof, but only offer a certain degree of moisture resistance.

Stator coated with insulating glue

To understand this, first look at the structure of an FPV motor (brushless outrunner motor):

  • Stator winding (coil): The surface is coated with insulating enamel and is inherently waterproof.
  • Permanent magnet: attached to the inner side of the rotor.
  • Bearing: a precise mechanical component that requires lubricating oil.
  • Rotor housing: rotating metal cover.

 

The key issue is that the motor is not sealed. During high-speed rotation, the motor actively draws in air-along with moisture and water. Once water enters, it primarily causes three types of damage:

  1. Bearing rust, lubrication failure-this is the most common and most fatal issue.
  2. Winding insulation performance degradation-leading to unstable current and reduced efficiency.
  3. The centrifugal force flings water onto the surrounding electronic equipment (ESC, flight controller), indirectly causing a crash.

 

Therefore, the motor coil itself is indeed not afraid of water, but the bearings are afraid of water, and the entire machine is even more afraid of water.

 

2

 IP waterproof rating: Understanding the "waterproof label" on the motor

 

Some high-end motors are labeled with IP ratings, helping you quickly assess their protection capabilities:

IP rating meaning representative product
IP25 Water spray resistance (2.5mm nozzle) Sparrow APM 2207.5
IP45 Waterproof against splashing (from any direction) T-Motor MN1123,Hobbywing V11122
IP53 Dustproof + Water-resistant TBS/Axisflying C series, VSD 3115
IP65 Dustproof + Splashproof T-Hobby V5315/V2808
IP67 Dustproof + Short-term immersion (up to 1 meter) DarwinFPV SeaWater Series

The higher the level, the stronger the protection. But note: IP67-rated motors are extremely rare in the FPV market.

 

3

 Truly "waterproof" motors on the market

Currently, there are very few FPV motors that can truly achieve "waterproof" (as opposed to just "water-resistant"):

 

1. DarwinFPV SeaWater series:

This is the only motor series on the FPV market that claims to be immersible in seawater without damage, boasting an IP67 waterproof rating.It features multi-layer anti-corrosion technology: oxidized magnets, stator electrophoresis coating, titanium alloy shaft, and stainless steel bearings. Official tests show it can still run smoothly after being submerged in seawater for over 12 hours. (Note: After seawater use, rinse the surface with fresh water to remove salt deposits.)

 

2. Motors with IP53/IP65 protection:

Such as the TBS/Axisflying C series (IP53) and T-Hobby series (IP65), which can resist water splashes and dust ingress but are not suitable for immersion.

 

3. Conventional FPV motor:

The vast majority of commercially available FPV motors lack any IP waterproof certification and can only be "resistant to moisture" rather than "waterproof."

 

4

 How to protect the motor from water damage

 

✅ Can do:

Apply conformal coating to the flight controller ESC and video transmitter

1. Apply conformal coating to the flight controller, ESC, and video transmitter:

This is the most effective method to protect the entire machine. But remember: Do not apply it inside the motor-the conformal coating will clog the bearings and cause the motor to seize.

Operating steps:

  • Clean the PCB with 99% alcohol.
  • Protect the USB port, barometer, buttons, and interfaces with masking tape.
  • Apply a thin layer of silicone conformal coating and wait for 15-20 minutes.
  • Apply the second layer, focusing on covering the solder joints and exposed circuits.
  • Check the coverage for completeness using a UV flashlight (the conformal coating contains a UV tracer).

2. Bearing maintenance:

  • After flight, if the motor gets wet, apply one or two drops of specialized bearing oil (such as Scorpion or Trinity) to the bearings.
  • Apply a small amount of dielectric grease or CorrosionX at the joint for moisture protection.

 

3. Post-flight processing:

If flown in light rain, power off immediately after landing and dry the motor internals with compressed air or a fan. If soaked in saltwater, rinse thoroughly with distilled water first, then soak in isopropyl alcohol and air dry.

 

4. Waterproofing of motor wire interface:

The motor wire connection to the ESC is sealed with adhesive heat shrink tubing (marine grade).

 

❌ Don'ts

  • Do not spray WD-40 into the motor-it will dissolve the existing lubricant.
  • Do not apply conformal coating to the interior of the motor.
  • Do not block the motor's cooling vents.
  • Do not fly in heavy rain or thunderstorms.

 

5

 Summary

 

Are FPV motors waterproof? The vast majority are not waterproof, only offering some moisture resistance.
Is the coil afraid of water? No worries-it's protected by insulating paint.
Are bearings afraid of water? Very afraid-getting wet will cause rust and loss of lubrication.
Can it fly in light rain? Yes, but there are risks-waterproofing the entire device + post-flight maintenance is required.
Are there truly waterproof motors? Available-such as the DarwinFPV SeaWater series (IP67)
Do you need to buy a waterproof motor? Most players don't need it-just maintain and protect it properly.
   

In summary: FPV motor coils are naturally waterproof, but the bearings are the Achilles' heel. It's okay to fly in light rain, but ensure the entire drone is waterproofed, shorten flight time, and perform immediate maintenance after flying. Only when truly submerging or flying over seawater should IP67-rated specialized waterproof motors be considered.

FAQ

Q: My FPV motor accidentally fell into the water. Can I use it directly after picking it up?

A: Never power it on directly! Remove the motor first, rinse it thoroughly with distilled water (especially if it's saltwater), then soak it in Isopropyl Alcohol (IPA) for a few minutes to displace the moisture. Finally, use a hairdryer (cold air setting) or compressed air to dry it completely. After drying, apply specialized bearing oil to the bearings and manually spin the rotor to check for smoothness. If the coils aren't burned and the bearings aren't rusted stuck, it usually can be revived.

Q: Can I fly FPV in heavy rain?

A: Strongly not recommended. Even motors with an IP65 rating can only withstand water jets, not the sustained deluge of heavy rain. Heavy rain will not only cause motor bearings to rust quickly, but more critically, water will travel down the motor wires to the ESC and FC, causing short circuits and crashes. If you absolutely must fly in the rain, make sure to apply Conformal Coating to the FC, ESCs, and VTX, and use physical covers for the entire drone.

Q: Are waterproof motors completely maintenance-free?

A: No. "Waterproof" does not mean "maintenance-free". Waterproof motors (like IP67-rated ones) primarily protect the coils and magnets, but the bearings are still mechanical wear parts. After long-term high-speed operation, the lubricating oil inside the bearings will evaporate or degrade. It is recommended to add bearing oil every 20-30 flight sessions, or after any water-contact flight. Additionally, after wet flights, it's best to invert the drone and run the motors idle for a few seconds to use centrifugal force to eject any trapped water.

Q: Why don't most manufacturers simply make all motors IP67 waterproof?

A: There are three main reasons: ① Cost – Fully sealed structures and specialized anti-rust materials significantly increase the price (e.g., DarwinFPV SeaWater series); ② Heat Dissipation – Complete sealing severely impacts air cooling efficiency, increasing the risk of high-temperature demagnetization; ③ Weight – Additional sealing layers compromise the lightweight design. For the vast majority of racers and freestyle pilots, lightweight and high power-to-weight ratio are far more important than waterproofing.

Q: Can I waterproof my motor by applying Conformal Coating? Can I brush it inside the motor?

A: Absolutely NOT! Conformal Coating should be applied to the FC, ESC, and VTX circuit boards, and should never be applied inside the motor. The motor has precision bearings and extremely tiny air gaps. If Conformal Coating seeps in, it will solidify, glue the bearings, or increase rotor resistance, directly jamming and ruining the motor. Motor "waterproofing" relies on physical structural design, not chemical coatings.

 

Send Inquiry